x
Send Your Inquiry Today
Quick Quote
  • ZY-368Y Fully Automatic Edge Banding Machine
  • ZY-368Y Fully Automatic Edge Banding Machine
  • ZY-368Y Fully Automatic Edge Banding Machine
  • ZY-368Y Fully Automatic Edge Banding Machine
  • ZY-368Y Fully Automatic Edge Banding Machine
  • ZY-368Y Fully Automatic Edge Banding Machine
  • ZY-368Y Fully Automatic Edge Banding Machine
  • ZY-368Y Fully Automatic Edge Banding Machine
  • ZY-368Y Fully Automatic Edge Banding Machine
  • ZY-368Y Fully Automatic Edge Banding Machine

ZY-368Y Fully Automatic Edge Banding Machine

The ZY-368Y is configured for continuous straight-panel edge banding where pre-milling, conveyor-based process synchronization and powered panel-thickness adjustment are required. It combines panel preparation, gluing, pressure bonding, end trimming, rough and fine trimming, scraping and polishing in one through-feed process.

• 14–25 m/min feed speed for continuous straight-panel production
• Processes 0.3–3 mm edge tape and 10–60 mm furniture panels
• Diamond pre-milling prepares the panel edge before adhesive application
• Conveyor encoder provides motion feedback for process-unit synchronization
• Powered pressure-beam adjustment simplifies panel-thickness changeovers

ItemSpecification
ModelZY-368Y
Feed Speed14–25 m/min
Edge Tape Thickness0.3–3 mm
Panel Thickness10–60 mm
Minimum Panel Length≥120 mm
Minimum Panel Width≥80 mm
Pre-MillingStandard
Dust RemovalStandard, confirm unit type
Conveyor EncoderStandard
Pressure-Beam AdjustmentPowered / electric adjustment
Adhesive SystemEVA supported; PUR optional
Heating Temperature130–220°C
Panel Preheating40–60°C
Pressure SystemMulti-stage pressure rollers
End TrimmingFront/rear end trimming
Trimming SystemSeparate rough + fine trimming
Edge ScrapingDouble-sided scraping
PolishingDual cloth-wheel polishing
ControlPLC touchscreen
Power Supply380V / 50Hz
Total PowerApprox. 22–26 kW
Machine DimensionsApprox. 7200 × 1000 × 1650 mm
Machine WeightApprox. 3500 kg
Automatic Corner RoundingNot listed as standard
ProcessFunction
Pre-MillingRemoves minor saw marks and irregularities from the panel edge
Dust RemovalClears loose dust around the pre-milling area
Panel PreheatingPrepares the panel edge before hot-melt adhesive application
Edge Tape FeedingFeeds compatible edge tape into the bonding section
Glue ApplicationApplies hot-melt adhesive
Pressure BondingPresses the edge tape against the panel
End TrimmingRemoves excess tape from the leading and trailing ends
Rough TrimmingRemoves the main excess upper/lower edge material
Fine TrimmingForms the finished upper and lower edge profile
Edge ScrapingRefines the trimmed edge surface
PolishingCleans and finishes the processed edge
RequirementZY-368Y
Straight panel processingYes
Pre-millingStandard
Dust removalStandard
Conveyor encoderStandard
Powered pressure-beam adjustmentStandard
End trimmingStandard
Rough trimmingStandard
Fine trimmingStandard
Edge tape thickness0.3–3 mm
Panel thickness10–60 mm
Feed speed14–25 m/min
EVA adhesiveSupported
PUR adhesiveOptional
Automatic corner roundingNot listed as standard

Choose the ZY-368Y when your production requires pre-milling, encoder-supported process coordination, powered thickness adjustment and separate rough/fine trimming in one through-feed machine. If pre-milling and powered adjustment are not required, a simpler configuration such as the ZY-368 may be more appropriate.

Diamond Pre-Milling and Dust Removal

Diamond Pre-Milling and Dust Removal

The ZY-368Y uses diamond pre-milling cutters to remove minor saw marks, burrs and edge irregularities before adhesive application. This prepares a flatter and cleaner bonding surface before the panel enters the gluing and pressing stages.

A dust-removal unit helps clear loose chips and dust produced around the pre-milling area. The exact dust-removal method and extraction requirements should be confirmed in the supplied machine configuration.

Conveyor Encoder for Process Synchronization

The conveyor encoder tracks conveyor movement and provides motion feedback to the control system. This information can be used to coordinate the timing of edge-banding process units as the panel moves through the machine.

The encoder should be described as a process-synchronization and conveyor-position feedback device rather than as a general machine-accuracy specification unless a verified positioning tolerance is available.

Conveyor Encoder for Process Synchronization
Powered Pressure-Beam Adjustment for Thickness Changeover

Powered Pressure-Beam Adjustment for Thickness Changeover

The ZY-368Y uses powered pressure-beam height adjustment to adapt the upper pressure structure to different panel thicknesses. This reduces the amount of manual height adjustment required when switching between compatible panel specifications.

Panel thickness must still remain within the confirmed 10–60 mm working range.

What is the main difference between the ZY-368Y and ZY-368?

The ZY-368Y adds pre-milling, a conveyor encoder and powered pressure-beam adjustment to a configuration that also includes rough and fine trimming. The ZY-368 is better suited when rough and fine trimming are required without these additional preparation and adjustment functions.

What does the conveyor encoder do on the ZY-368Y?

The conveyor encoder provides motion feedback to the control system so that applicable processing units can be coordinated with panel movement through the machine. It should not be interpreted as a published positioning-accuracy tolerance unless a measured value is provided in the technical specification.

What panel and edge-tape range does the ZY-368Y support?

The listed configuration processes 10–60 mm panels and 0.3–3 mm edge tape, with a minimum panel length of 120 mm and minimum width of 80 mm. Final compatibility should be confirmed using your actual workpiece specifications.

Can the ZY-368Y use PUR adhesive?

EVA is supported, while PUR is available as an option. The PUR melting system, cleaning procedure and maintenance requirements should be confirmed in the quotation.

Does the ZY-368Y include automatic corner rounding?

Automatic corner rounding is not listed as a standard function in the current ZY-368Y model configuration. If corner finishing is required, send your panel, edge-tape and finished-edge requirements for another configuration comparison.

Send Your Inquiry Today
Quick Quote

About Shandong Yuehe Machinery Co., Ltd.

Yuehe designs and manufactures automatic edge banding and panel-processing equipment in Ningjin County, Dezhou, Shandong, China. Available services include machine configuration, factory testing, remote installation guidance, operator training and spare-parts support, subject to the confirmed sales contract.
Scroll to Top